(MT-01) Informazioni tramite gli strumenti (in inglese)

[soapman]

SPEEDOMETER AND ELECTRICS

 

Q: How do I change between miles and kilometers?

 

- with the ignition key ON

- press and hold SELECT button for at least 2 sec

 

Q: How do I adjust time?

 

- with the ignition key ON

- press and hold both SELECT and RESET buttons for at least 2 sec

- press RESET button to set hours

- press SELECT button

- press RESET button to set minutes

- press SELECT button

 

Q: How do I change speedometer illumination?

 

- with the ignition key OFF

- press and hold SELECT button

- then turn the ignition key ON

- and continue to hold SELECT button for at least 5 sec

- press RESET button to adjust the tachometer panel brightness

- press SELECT button

- press RESET button to adjust LCD brightness

- press SELECT button

- press RESET button to adjust the tachometer needle brightness

- press SELECT button

 

Q: How do I enter and use DIAG mode?

 

- with the ignition key OFF

- press and hold RESET button

- then turn the ignition key ON

- and continue to hold RESET button for at least 8 sec

- press SELECT button, after "dIAG" appears on LCD

- press and hold both SELECT and RESET buttons for at least 2 sec

- switch ENGINE STOP button (the red one) off

 

- press SELECT button to cycle thru sensors/actuators

- press ENGINE STOP button on to read sensor value / execute actuator

 

For example, if you want to check the engine temperature, press SELECT few times to go to the number "11" and switch ENGINE STOP button on. Note that with some sensors/actuators you need to do additional things, like spin the wheel, or crank the engine. Check the Service Manual for details.

 

Q: What are ECU fault codes in brief?

 

12 - crankshaft position sensor

15 - throttle position sensor (TPS)

13 - cylinder #1 intake air pressure sensor (MAP)

14 - cylinder #1 intake air pressure sensor (MAP)

25 - cylinder #2 intake air pressure sensor (MAP)

26 - cylinder #2 intake air pressure sensor (MAP)

17 - EXUP servo motor

18 - EXUP servo motor

22 - air temperature sensor (IAT)

28 - engine temperature sensor (ECT)

29 - decompression solenoid

38 - decompression solenoid

30 - vehicle has overturned

33 - cylinder #1 ignition coils

34 - cylinder #1 ignition coils

35 - cylinder #2 ignition coils

36 - cylinder #2 ignition coils

37 - idle valve (ISC)

42 - speed sensor or neutral switch

43 - ECU (battery) voltage

46 - ECU (battery) voltage

62 - muffler temperature sensor

63 - muffler temperature sensor

50 - faulty ECU

 

Q: What is sensors and actuators test table in brief?

 

01 - throttle angle (TPS)

03 - cylinder #1 intake air pressure (MAP)

04 - cylinder #2 intake air pressure (MAP)

05 - air temperature (IAT)

07 - vehicle speed pulse

08 - lean angle cut-off

09 - ECU (battery) voltage

11 - engine temperature (ECT)

12 - muffler temperature

20 - side-stand switch

21 - neutral switch

30 - cylinder #1 ignition coils

31 - cylinder #1 ignition coils

32 - cylinder #2 ignition coils

33 - cylinder #2 ignition coils

36 - cylinder #1 injector

37 - cylinder #2 injector

49 - intake solenoid ("flapper")

50 - fuel pump

51 - muffler cooling fan

52 - headlight

53 - EXUP servo motor

54 - idle valve (ISC)

55 - decompression solenoid

[toif]

:-k Luca.....già che c' eri potevi tradurre in Italiano :mrgreen: :smt005

 

:smt006 :smt006